Barkbusters Blizzards fitting
+4
F
madmax
paul
potatomasher
8 posters
Page 1 of 1
Barkbusters Blizzards fitting
hello there - has anyone fitted these? i got some the other day and according to the instructions you use the original end weight bolt to hold them on. so i unscrewed the right hand bolt and pulled it out however when attempting to screw it back it, the bolt [which is quite long] is now rotating in thin air and not going into whatever was in before. the left hand side seems ok. so the question is what's inside there - i have a feeling i should have loosened it and pulled whatever it screws into out as well.....
any thoughts?
any thoughts?
_________________
Re: Barkbusters Blizzards fitting
I've never fitted Barkbusters , but the end weight bolt pulls up on a rubber grommet with a" loose" nut on the other side of the grommet . The bolt should only be loosened ( not removed ) & then pushed in to release the force on the grommet & then pull the whole assembly out.You now have the option of buying another grommet , nut etc & leaving the old one in there , or taking the other side weight out & poking something through the bars to push it out ( small piece of rag on a piece of stiff wire ).
_________________
Four wheels move the body. Two wheels move the soul.
paul- Posts : 7738
Join date : 2011-08-19
Age : 71
Location : Morphett Vale Sth. Aust.
Re: Barkbusters Blizzards fitting
good thinking - i will try the stiff wire process and poke it out [ it doesnt mention that in the manual though]
_________________
Re: Barkbusters Blizzards fitting
Although not seeing how the instructions are written I would expect the intent is to remove the bar end as a whole, attach it to the barkbuster then re-insert into handle bar and tighten up.
Good instructions would have come with a warning not to do what you have done.
If you can't push it out from the other side, you could try making a small hook out of some stiff wire and try pulling it out.
Good luck.
Good instructions would have come with a warning not to do what you have done.
If you can't push it out from the other side, you could try making a small hook out of some stiff wire and try pulling it out.
Good luck.
_________________
2020 BMW R1250RS Exclusive
madmax- Posts : 4305
Join date : 2011-10-19
Age : 60
Location : Carrum Downs, Victoria
Re: Barkbusters Blizzards fitting
yep did the same thing the first time, but never again,just loosen bolts to get them to pull out.A thin but solid bit of wire with a slight hook on the end and some patience managed to save the day.
Good luck.
Good luck.
F- Posts : 59
Join date : 2011-08-03
Age : 76
Location : cruiswers carwash port pirie.
Re: Barkbusters Blizzards fitting
I did the same thing the other day fitting my heated grips. If you take the bolt out and gently push it in and turn at the same time you may be able to grab the nut.
Worked for me.
Otherwise I'd use a bit of coat hanger wire with a hook on the end to pull the rubber out then the nut should just fall out.
Phil.
Worked for me.
Otherwise I'd use a bit of coat hanger wire with a hook on the end to pull the rubber out then the nut should just fall out.
Phil.
lacko- Posts : 23
Join date : 2015-01-04
Re: Barkbusters Blizzards fitting
Been there and done that myself. I used the air compressor to blow it out then put a dob of black silicone on the end of the bolt so the nut wouldn't be able to unwind too far
_________________
My posts reflect my personal experience or opinion. You don't have to agree with me.
~ Chris ~~ 0466 Ask ~
~ My Photography Blog Page ~
~ My YouTube Channel ~
~ Suzuki Bandits Australia Facebook Page ~
~ Half hr from the hills. Two minutes from the coast ~
~ My Bike ~
BMW R1250RS
Re: Barkbusters Blizzards fitting
Good idea, a spot of weld would be even better
_________________
2020 BMW R1250RS Exclusive
madmax- Posts : 4305
Join date : 2011-10-19
Age : 60
Location : Carrum Downs, Victoria
Re: Barkbusters Blizzards fitting
GUILTY !
Did the same thing too....the first time. Just loosen it and remove the bar-ends with the rubber grommets still attached.
I used a long threaded coachbolt to grab the rubber grommet left inside the handle bars......it worked for me.
Did the same thing too....the first time. Just loosen it and remove the bar-ends with the rubber grommets still attached.
I used a long threaded coachbolt to grab the rubber grommet left inside the handle bars......it worked for me.
Handy1250FA- Posts : 55
Join date : 2014-02-16
Location : Sydney Australia
Re: Barkbusters Blizzards fitting
I added some ally strap to the inner edge on mine as I have heated grips and extra switch gear on the bars and did not like the way the existing strap clamped over these items.
As pictured: Hope it helps someone.
As pictured: Hope it helps someone.
Similar topics
» Help with fitting new chain please
» Pazzo Levers and Barkbusters
» Odds & Ends
» Barkbusters Storm handguns and some 3" led spotlights.
» Bypass O2 sensor
» Pazzo Levers and Barkbusters
» Odds & Ends
» Barkbusters Storm handguns and some 3" led spotlights.
» Bypass O2 sensor
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum
|
|